![]() Insert the tag end of the serving above the peep, so it slides in between the two bundles. To begin, take about two feet of serving material, then create a “mini” center serving on the string, just above the peep. To serve a peep in correctly, create small bundles of serving (about 3/8 to 1/2-inch thick) above and below the peep. This fiber is strong and lays down super smooth. For serving, I favor BCY’s 3D End Serving, which is. To serve the peep, you’ll need some serving material, scissors, and a cigarette lighter. This will maintain a solid squeeze on the peep without excessive string friction against the peep’s body. Each bundle has the ability to creep imperceptibly away from the bowstring’s “V” located above and below the peep’s location. (3) Two serving bundles prevent excessive “pinching” of the peep sight against the string fibers, which can cause undue wear and torque on the fibers. (2) If the peep needs to be moved, the bundles can be separated, then the peep can be nudged up or down the string to optimize alignment with the shooter’s eye. This method works best for three reasons: (1) When served correctly, two bundles secure the peep nicely, without fear of it dislodging. However, I prefer to serve using two separate serving bundles. There are several ways to tie in a peep sight. To find the natural split, you may have to untwist the bowstring quite a bit in order to see the separation in the bundles. If not, the bowstring won’t rotate naturally, eventually causing issues with the peep’s alignment. The peep should be sandwiched between these bundles. Every bowstring made is looped together using two sets of fibers. It’s also important to find the natural “split” in the string. However, if the string isn’t two-colored and doesn’t have a tag string in place, you’ll have to count how many fibers are in the entire string, divide it by two, then put the peep in between the bundles. ![]() This makes inserting the peep super simple. Most bowstrings today are two-colored and come complete with a small tag that divides the fiber bundles evenly. One critical part in this step is splitting the fibers. Be sure the fibers are nestled within the notches on the peep’s body, placing it at a slight angle. Once the bowstring is relaxed, you can install the peep correctly by splitting the bowstring fibers and then inserting the peep, so it bisects your marker’s tick mark. The EZ-Press by Last Chance Archery is my preferred choice. With today’s extreme pre-loaded bow limbs, I prefer to use a press that absolutely minimizes stress on the bow’s limbs and riser. To install a peep, you must compress the bow’s limbs using a high-quality bow press. This is a great starting point position to place the peep. Then have a friend make a small tick mark, using the Sharpie pen, along the bowstring directly across from your eye. Draw the bow back, close your eyes, then find the most comfortable draw-anchor position. Ideally, the shooter should be super comfortable at full draw, even when shooting at sharp angles.Ģ. If it’s in the wrong spot, it’ll disrupt the archer’s natural anchor position. How the peep is positioned on the bowstring is critical. This string angle ultimately determines where the peep should be located based on anchor position and the center of the shooter’s eye. Why? Because every bow is different and exhibits a unique string angle at full draw, based on axle-to-axle length, cam design, and brace height. Use a light tick mark on the string, since this is still a rough measurement. Use a Sharpie pen to mark where the peep should go, based on this measurement. Then, take this measurement and transfer it over to the new bow. On your old bow, measure the distance from the top of the string loop or nocking point to the center of the peep sight. To do this, choose one of the following steps:ġ. Perhaps the most challenging part of installing a peep sight, particularly on a new bow, is making sure it goes in the right place. Step 1: Identify the Best Location for the Peep Here’s the best way to handle this archery task in five simple steps. ![]() This seemingly simple chore can sometimes be a nightmare, particularly if you don’t have the right tools, know-how and system for positioning the peep in the perfect spot to enhance proper shooting form. You simply split the bowstring, plop the peep inside, then serve it in place. Installing a peep sight on a bow is not rocket science. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |